Makita 2030 manual planer jointer pdf 46 Mb Free print. Repair Parts Home Power Tool Parts Makita Parts. PDF, makita, 2030, jointer, planer, manual. Makita 2030 Planer Blades (post. I have two questions regarding a Makita 2030 Planer/Jointer combo I. The knives to the planer head? For some reason the manual.

• 3 0 (118') size lmml Fence size 19-1 1/16') 35~7116') 100 124~7132' lmml Overall dimensions 574 (27~23132' 35~7116' 22~19132') MODEL 2030s DOUBLE INSULATION Feed rateimin 5-29132'1 wide 9-7/16'] 10.5 (34.5 wide 12-9/32'] w i d e lmml (mml Stock height 160 15/32'. • For Your Own Safety Read Instruction Manual Before Operating Planer-Jointer GENERAL SAFETY PRECAUTIONS KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn the tools applications and limitations, as well as the specific potential hazards peculiar t o KEEP GUARDS IN PLACE and in working order. • EXTENSION CORDS.

Make sure your extension cord is When using an extension cord, be sure t o use one heavy enough t o carry the current your product will draw. A n undersized cord will cause a drop in line voltage resulting correct size t o use depending on cord length and nameplate ampere rating. • Never stick your finger into the chip chute. Chute may jam w h e n cutting damp wood. Turn off the planer-jointer and then clean out chips w i t h a stick. Do not touch blades right after operation, they may be extremely hot and could burn your skin.

• FOR AUTO-PLANER Two or more pieces of narrow but similar thickness stock can be passed through the auto-planer side by side. However, allow some spacing between the stock t o permit the feed rollers t o grip the thinnest piece. • When transporting it by vehicle, secure with a rope or other substantial means to prevent tipping or movement. Positioning the planer-jointer Locate the tool in a well lit and level place where you can maintain good footing and balance.

• AUTO-PLANER FUNCTIONS: Dimensional adjustment Raise the table by turning the crank handle clockwise until the indicator plate points to the scale graduation indicating the de- sired finished dimension. One full turn of the crank handle moves the table 2 mm (3/32') • This i s especially convenient with two operators. CAUTION Workpieces with the following dimensions cannot be fed into the auto-planer because the interval between the two feed rollers i s 114 mm (4-1/2'). Do not try to cut them. Less than (4-1i2') • JOINTER FUNCTIONS: Extension support table The extension support table i s convenient for cutting long workpieces. Install it on the outfeed table and semi-tighten the four hex bolts. Extend the legs arms over the screw using the hook Then tighten the screws securely.

Adjust the table height using the knobs so that the extension support table i s level with the outfeed table. • Adjusting the fence angle The fence angle can be adjusted angle from 0’ to 45’. Loosen the clamp screws ( A ) and (B) and pull the fence out slightly. Drivers Trendnet Rtl 8139d. Then tighten the clamp screws (A) and (B). Loosen the hex bolts ( A ) and (B) and tilt the fence according to your work. • Carefully maintain flush, steady con- tact with the fence while making the cut.

REPLACING THE PLANER BLADES Dull blades can cause a rough finish, an overload of the motor and dangerous kickback of the workpiece. Sharpen or replace dull blades immediately. This tool is equipped with either throw-away blades or standard blades. • The magnetic holder has a different shaped claw on each side. Use the cor- rect claw for auto-planer. Place the two magnetic holders on the set plate and push them in the direction of the arrow until the claw contacts the blade. Remove the eight blade installation bolts using the socket wrench.

• Place the two magnetic holders on the push them until the claw contacts the blade (Note: Use the correct claw for auto-planer. Grip the magnetic holders and slip the heel of the plate into the groove in the drum. Install the blade installation bolts. • Install the other blade as described above. Rotate the drum slowly while pressing the lock plate to make sure there i s nothing abnormal. Mengatasi Adobe Premiere Expired Green.

Then close the chip cover and secure using the hex bolt. CAUTION: Do not tighten the blade installation bolts without the blade locating lug of the correctly resting in the groove of the blade. Removing the blades CAUTION Always close the chip cover over the auto-planer before removing the blade. Lower the infeed table fully by turning the depth adjusting knob clockwise. Loosen the hex bolt which secures the safety cover rod and lift off the safety cover. • Installing the blades Provide a flat wood block approx.